Talk like the crew
Jobsite words: a glossary for greenhorns
Updated
Every crew has its own words, and knowing them on day one tells the foreman you did your homework. Here are the ones you will hear first in each trade. Learn them, then listen for the ones your crew uses that are not here.
Linework
- Tailboard
- The pre-job safety talk at the truck before work starts.
- Groundman
- The crew member who works the ground end of the job and supports the linemen.
- Hot stick
- An insulated pole used to work on or near energized lines.
- Handline
- The rope used to raise and lower tools and material to the lineman.
Electrician
- Rough-in
- Boxes, conduit and wire installed before the walls are closed.
- Trim out
- Installing devices, covers and fixtures after the walls are finished.
- Home run
- The cable run from the panel to the first box on a circuit.
- Box fill
- The code limit on how many wires and devices fit in one box.
Plumbing and pipefitting
- Top out
- The stage when drain, vent and supply pipe are in the walls before cover.
- Sweat a joint
- Solder a copper joint with a torch.
- Cleanout
- An access point for clearing a drain line.
- Dope
- Pipe joint compound used on threads.
HVAC
- Lineset
- The pair of copper lines that carry refrigerant between the units.
- Pull a vacuum
- Remove air and moisture from the system before charging it.
- Superheat
- A temperature reading techs use to judge refrigerant charge.
- No-cool
- A service call where the air conditioning is not cooling.
Welding
- Root pass
- The first weld pass at the bottom of the joint.
- Cap
- The final pass on top of the weld.
- Fit-up
- How the pieces are lined up and tacked before welding.
- Slag
- The crust left on top of a stick or flux-core weld.
Heavy equipment
- Walkaround
- The pre-shift inspection of the machine.
- Grade stake
- A marked stake showing how much to cut or fill.
- Swing radius
- The area a machine's upper body can sweep. Nobody belongs in it.
- 811
- The national call-before-you-dig number to get underground utilities marked.
Truck driving
- Pre-trip
- The required inspection of the truck before driving.
- Deadhead
- Driving empty to the next load.
- Bobtail
- Driving the tractor without a trailer.
- GOAL
- Get out and look before you back up.
Millwright
- Soft foot
- A machine foot that does not sit flat, which throws off alignment.
- Shim
- Thin metal used to level or align a machine.
- Dial indicator
- A gauge that measures small movement during alignment.
- Lockout
- Locking out energy sources before work starts.
Process operator
- The board
- The control room screens operators watch.
- Rounds
- Walking the unit to check equipment by eye and ear.
- Turnaround
- A planned shutdown for maintenance and repairs.
- Permit to work
- Written approval before maintenance work starts in the unit.
Roofing
- Square
- One hundred square feet of roof.
- Tear-off
- Removing the old roof down to the deck.
- Flashing
- Metal that seals walls, chimneys and pipes against water.
- Starter course
- The first row along the eave that the rest of the roof sits on.
Septic and sewer
- Baffle
- The tee or wall inside the tank that keeps solids out of the drain field.
- Riser
- A pipe or collar that brings the tank lid up to ground level.
- Drain field
- The buried area where treated water soaks into the soil.
- Pump-out
- Removing the sludge and scum from a septic tank.
Pipeline and pipelayers
- Spread
- The full pipeline crew working one section.
- Stringing
- Laying pipe joints out along the ditch.
- Holiday
- A gap or flaw in the pipe coating.
- Side boom
- A tractor with a boom that lifts and lowers pipe.
Oilfield
- Lease
- The well site and the land around it.
- JSA
- Job safety analysis, a written check of the hazards before work.
- Tripping pipe
- Pulling pipe out of the well or running it back in.
- Doghouse
- The small shed on the rig floor.
Waste hauling
- Rear loader
- A truck loaded from the back, often with a helper.
- Side loader
- A truck with an arm that grabs cans from the side.
- Hopper
- The opening where the load goes in.
- Roll-off
- A large open container dropped at a site and hauled away full.
Landscaping
- Base
- The compacted crushed rock under pavers or a wall. Everything above it depends on it.
- Lift
- One layer of base or fill, compacted before the next goes on.
- Screed
- Dragging a straight board across sand to make a flat bed for pavers.
- Plate compactor
- The vibrating machine that packs base rock and pavers; also called a plate tamper.
- Zone
- One section of a sprinkler system that runs off a single valve.
- 811
- The national call-before-you-dig number that sends locators to flag buried lines.
Want more on how a good crew works? Read the crew codes.